Compact heating and cooking stove e thermal cabinet konetruktsii Potapov

Heating and cooking stove designs VA Potapov (Fig. 87) has a relatively small size: its length is 630 mm, width - 510 mm, height - 1820 mm, so the masonry stoves need only 211 bricks.

Малогабаритная отопительно-варочная печь с тепловым шкафом конструкции В. А. Потапова
Fig. 87. Compact heating and cooking stove with a heat cabinet design VA Potapov.



Heat transfer furnace at one fire per day - 850 kcal / h, with two furnaces - 1300 kcal / h
The furnace is mounted on a solid foundation with two-ply waterproofing, joined to the wall

chimney, shaft-mounted or indigenous pipes. Hearth furnace produced only in winter.
Consider the features of the unit furnace. Cooking chamber with a door located on the cast-iron stove. Inside the chamber, provided the vent or pipe diameter of 60 mm, used to remove odors. The oven is above the cooking chamber. Hot gases pass through the channel from the iron plate beneath the oven, heat it with the bottom and back side and only then sent to the flue.
Materials for masonry stove:
- Ordinary brick - 211 pc.
- Cast iron plates 360 x 410 mm, with a hob - 1 piece.
- Furnace door is 130 x 210 mm - 1 piece.
- The ash-pit door 130 x 140 mm - 1 piece.
- The clean door 130 x 140 mm - 1 piece.
- Cast-iron to the duct 130 x 75 mm - 1 piece.
- Grill grate 180 x 200 mm - 1 piece.
- Furnace valve 140 x 140 mm - 1 piece.
- Corner of steel 32 x 32 x 4 mm - 8 pc.
- Steel wire knitting 1.5-1.8 mm - 4.5 m;
- Iron roof 500 x 700 mm - 0.35 m;
- Roofing - 1.0 m
Laying sequence is shown in Figure 88.

Последовательность кладки печи конструкции В. А. Потапова
Последовательность кладки печи конструкции В. А. Потапова



Fig. 88. The sequence of construction of masonry stoves VA Potapov.


1st row - from a brick laid horizontally.
2nd row - lay the channel size of 140 x 260 mm, set the clean door.
Third row - ash unit and strengthen the door for him.
4th row - floor cleaning (ashpan left unchanged).
5th row - is laid out according to poryadovkoy. Set grate, with the front and back of the firebox abate brick. Channel dimensions remain unchanged.
6th row - installation of the fire door.
7th row - is laid out similarly to the 6th row in compliance with bandaging joints.
8th row - device overlap the firebox door to form holes for laying the iron plate. On the right side, leave the channel through which gases will be released into an existing channel.
9th row - is laid out similar to the 8th row in compliance with bandaging joints.
10th row - is laid out according to poryadovkoy. Set the cooking chamber door. On the left and put the back of the wall thickness of a quarter-brick to expand the camera.
11-12-th series - are laid out in accordance with poryadovkoy.
13th row - in this series should be left hole on the right side, which will be installed door to ventilate the cooking chamber.
14th row - to increase the height of the camera in the upper left part of the hole.
15th row - is the ceiling for the 14th series.
In this series, should leave one channel, which runs from the 2nd row.
16-17-th series - setting door cleaning.
18-23rd series - are laid out in accordance with poryadovkoy. Set the oven.
24 and subsequent rows - top floor unit furnace, smoke valves.
Share with your friends a link to this page, or add to