Heating and cooking stove designs Buslaeva

It is very user-friendly design, providing mostly lower heating and cooking stove with oven. While oven is quite compact (1020 x 770 x 2010 mm), has a high heat and can heat the room a large area (Figure 71).

Отопительно-варочная печь конструкции К. Я. Буслаева
Fig. 71. Heating and cooking stove designs KY Buslaeva.



Materials:
- Ordinary brick - 382 pc.
- Refractory bricks - 43 pc.
- Furnace door is 250 x 205 mm - 1 piece.
- The ash-pit door 140 x 140 mm - 1 piece.
- The cooking chamber door 500 x 390 mm - 1 piece.
- Brass cabinet 500 x 330 x 280 mm - 1 piece.
- Cast iron stove with two 700 x 400 mm - 1 piece.
- Smoke damper 250 x 130 mm - 1 piece.
- Valve parovytyazhnaya 130 x 130 mm - 1 piece.
- Grate 200 x 300 mm - 1 piece.
- Corner of steel 45 x 45 x 1010 mm - 3 pc.
- Strip steel 350 x 25 x 3 mm - 4 pc.
20 x 25 x 2 mm - 4 pc.
1010 x 50 x 4 mm - 4 pc.
750 x 50 x 4 mm - 4 pc.
- Roofing steel sheet 300 x 280 mm - 1 piece.
- Tiles, cast iron 400 x 250 mm, 400 x 150 mm - 2 pcs.

Laying sequence is shown in Figure 72.
Последовательность кладки печи конструкции К. Я. Буслаева

Fig. 72. The sequence of construction of masonry stoves KY Buslaeva (dimensions in mm).

1st row - solid masonry in the drawing.
2nd row - repeat 1st row with compulsory ligation sutures. Installing the ash-pit door.
N-th row - fixing the ash-pit door. Under the oven is left an opening for the clean windows.
4th row - masonry foundation under the oven, which is draped from the firebox with refractory brick and corrugated iron sheets reinforce the other three sides.
5th row - setting the grate, laying refractory brick base of the fire,
installing the firebox door, blocking the ash-pit door and the clean windows. b-th row - fixing the firebox door and the oven.
7th row - obkladyvanie firebrick put on edge, wall oven.
8th row - laying in the drawing.
9th row - oven for 1 cm covered with clay mortar, steel strip cover the firebox door. Establish an iron stove with burners, building it into strips 10 mm steel.
10th row - start laying dymooborota. Leave a window cleaner, stove with burners not lay. From plate clutch are on edge.
11th row - first floor cleaning device has sunk two channels for cleaning. The bricks of the series to have two steel strips about 25 cm in length, which will serve as the basis for the suspension of the walls.
12th row - overlap cleansing sunk channels. Attached wire, fixing door frame cooking chamber.
13th row - laying bricks, set at the edge of the device cap-steam chest.
14th row - the overlap of the cooking chamber. Left a hole for exhaust.
15th and 16th rows - laying in the drawing while leaving space for the two stoves.
17th row - small stove cover sheet of roofing steel, then lead the clutch according to the drawing.
18th row - the unit in the back of the stove the clean big hole. The inner walls of the first and second channels are brought to overlap by 20 and 13 cm, respectively. The upper edge of these walls abate.
19th row - brick lay flat, and outputting the oven for 30 mm projection.
20th row - the overlap of the chimney. Repeat overhang by 30 mm from the outside of the oven. Installing steel angle from the edge of the steel strip in the middle and to shut the stove.
21 th row - overlapping large stove and the chimney. In size, this series follows the 19th.
Installation of smoke and steam valves.
22th row - masonry stove neck in three rows. Gradually reduce the size of the chimney up to 13 x 26 cm for the subsequent installation of the second gate.
After that start mason chimney with cuts.
Share with your friends a link to this page, or add to